As Amazon Associates, we earn from qualifying purchases. This means we may receive a small commission at no extra cost to you if you click through and make a purchase.

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

This wassermann 4 deep well submersible review covers a pump built for 4-inch well casings and larger. It delivers a max flow of 33 GPM and a max head of 190 feet. The unit runs on 230V power with 1 HP of motor strength. Its stainless steel construction aims to resist corrosion. You get a 10-foot cable and a built-in control box for easier wiring. This model is designed for deep water extraction tasks.

  • Built-in control box eliminates the need for external boxes
  • Stainless steel body and SS304 pump head for durability
  • 1-1/4" FNPT outlet port for standard pipe connections
  • Operates on 230V/60Hz power supply
  • Max flow rate of 33 GPM at 190 ft head

Good fit for

You should choose this pump if you have a 4-inch or larger well casing. It suits users who need a 230V system for deeper water lifts up to 190 feet. The 33 GPM flow rate supports irrigation needs or livestock watering. The integrated control box simplifies installation for those who want to avoid extra components. If you need reliable groundwater extraction for home or farm use, this spec profile fits well.

Who can skip it

Skip this model if your well casing is smaller than 4 inches in diameter. You must also skip it if your electrical system only provides 115V power, as this unit requires 230V. The 10-foot cable may be too short for very deep wells without extension. If you need higher flow rates than 33 GPM, this pump will not meet your demands. Consider the 1/2HP 115V variation if you need lower voltage compatibility.

Verdict

This pump offers a solid spec sheet for 4-inch wells needing 230V power. It is a practical choice for irrigation and livestock setups requiring moderate flow.

01 Wassermann Pump Key Specs Explained

Voltage: 230V

This pump requires a 230-volt electrical circuit rather than standard 115V household outlets. You must verify your well has the correct power supply before installation. Using the wrong voltage can damage the motor or prevent operation entirely. This specification ensures compatibility with dedicated well circuits. It also influences the type of starter or control box needed for safe operation.

Horsepower: 1 HP

The 1 HP motor provides sufficient power to lift water from significant depths. This strength supports the stated 33 GPM flow rate against resistance. It is suitable for residential irrigation and livestock watering needs. Higher horsepower models exist for deeper wells or larger agricultural demands. This rating indicates a balance between performance and energy consumption for typical home use.

Max Flow Rate: 33 GPM

Gallons per minute measures how much water the pump moves. A 33 GPM rate is adequate for filling livestock tanks or watering gardens. It may not support multiple high-flow fixtures simultaneously in a large home. Compare this figure to your daily water usage requirements. It determines how quickly you can fill containers or irrigate fields efficiently.

Max Head: 190 ft

Head refers to the vertical height the pump can push water. A 190-foot max head limits the depth of your well or lift height. If your well casing exceeds this depth, the pump cannot deliver water to the surface. This spec is critical for matching the pump to your specific well depth. Exceeding this limit will result in zero or minimal flow.

Outlet Port Size: 1-1/4" FNPT

The outlet size determines the pipe diameter needed for connection. A 1-1/4-inch female national pipe thread requires matching fittings and tubing. Using smaller pipes can restrict flow and reduce efficiency. Larger pipes may require adapters. This standard size is common in residential well systems. Ensure your existing plumbing matches this specification for a leak-free installation.

02 Design and Build Overview

The listing states the pump body and head are made of stainless steel and SS304. This material choice suggests a design focused on resisting corrosion in deep well environments. You get a unit that weighs 28.7 pounds. Its cylindrical shape measures 3.74 inches in width and height, with a total length of 28.2 inches. These dimensions fit standard 4-inch well casings and larger. The compact footprint allows for easier lowering into narrow boreholes compared to bulkier alternatives.

You receive a 2-wire pump configuration with a ground wire. The listing notes a built-in control box, meaning you do not need to purchase or install an external one. This simplifies your electrical setup. The outlet port is 1-1/4 inch FNPT. You should install extra check valves at the outlet pipe to prevent flowback, as recommended by the manufacturer. The premium mechanical seal aims to prevent water leakage, which supports a longer service life.

The finish is described simply as stainless steel. This consistent material use across the body and head reduces the risk of galvanic corrosion between different metals. The design prioritizes durability in submerged conditions. You can use this layout for irrigation, livestock farming, or industrial drainage. The straightforward construction means fewer external components to maintain or replace over time.

03 Setup and Everyday Use Guide

You install this pump into 4-inch well casings or larger. The unit measures 28.2 inches in length and 3.74 inches in width. You lower the stainless steel body directly into the well water. The listing notes a 10-foot cable is included. You must connect this to a dedicated 230V/60Hz power source. This is not a standard household outlet. You need the correct voltage to operate the 1 HP motor. The pump features a built-in control box. This means you do not need to purchase or install an external control box. This simplifies your electrical setup significantly. You only need to wire the 2-wire plus ground connection. Once installed, the pump delivers up to 33 GPM of water. The maximum head height reaches 190 feet. You can use this flow for irrigation, livestock farming, or fish ponds. The outlet port is 1-1/4" FNPT. You should install extra check valves at the outlet pipe. This prevents water from flowing back into the well when the pump stops. The premium mechanical seal helps prevent leakage during operation. You can also use this for industrial drainage or river water extraction. The SS304 pump head and stainless steel body are designed for extended service life. You do not need to worry about frequent corrosion issues in typical well water. The design supports continuous use in agricultural or residential settings. You simply ensure your well casing is wide enough and your power supply matches the 230V requirement. The built-in controls handle the rest of the operational logic for you.

04 Before You Buy This Pump

Before you buy the Wassermann 1HP 230V Deep Well Pump, verify your well casing is four inches or wider. This unit requires a dedicated 230-volt circuit, not standard household outlets. You must install an external check valve at the outlet pipe to prevent water flowback, as the pump lacks internal backflow prevention. The 10-foot cable may be too short for deeper wells, so you might need a compatible submersible wire extension rated for wet environments. Ensure your electrical panel can handle the 1 HP load without tripping breakers. While this pump suits irrigation and livestock watering, it does not filter water. You still need a separate filtration system if your source contains sediment or contaminants. Check that your storage tank pressure settings align with the 33 GPM flow rate. This pump is a mechanical workhorse, not a smart device. It fits well alongside other deep well options if you prioritize raw power over digital controls. Confirm your plumbing uses 1-1/4 inch FNPT fittings before ordering.

Check before you buy

  • Verify your well casing is four inches or wider
  • Confirm you have a 230-volt electrical circuit available
  • Plan to install an external check valve at the outlet
  • Check if the 10-foot cable reaches your pump depth
  • Ensure your plumbing fittings match the 1-1/4 inch FNPT size
1
Wassermann 1HP 230V Deep Well Pump

Wassermann 1HP 230V Deep Well Pump

Best for: 230V deep well irrigation

Horsepower
1 HP
Pump Type
Deep Well Submersible Pump
Max Flow Rate
33 GPM
Max Head
190 ft
Voltage
230V
Housing Material
Stainless steel

The Wassermann 4" submersible pump delivers 33 GPM at a max head of 190 ft. It runs on 230V power and features a stainless steel body. The unit includes a built-in control box for 2-wire operation, removing the need for external components. This design suits users needing reliable groundwater extraction for irrigation or livestock. Its compact 4-inch width fits standard well casings.

Pros
  • Stainless steel construction resists corrosion
  • Built-in control box simplifies wiring
  • 33 GPM flow rate supports irrigation
  • 190 ft max head handles deep wells
Cons
  • 28.7 pounds weight adds lifting effort
  • 230V requirement limits voltage options
  • 190 ft head restricts deeper applications
Good fit if
  • You need a 4-inch pump for deep wells
  • You have 230V power available
  • You want stainless steel durability
Skip if
  • You only have 115V power
  • You need more than 190 ft head
  • You prefer lighter equipment

Verdict: Wassermann 4" 1HP Submersible Pump fits users with 230V power seeking a durable stainless steel pump for moderate depth wells. It works well for irrigation but may struggle with deeper heads.

05 Specifications side by side

SpecWassermann 1HP 230V Deep Well Pump
Horsepower1 HP
Pump TypeDeep Well Submersible Pump
Max Flow Rate33 GPM
Max Head190 ft
Voltage230V
Housing MaterialStainless steel
Outlet Port Size1-1/4" FNPT
ApplicationIrrigation
MaterialStainless Steel
Intended UseHome
Dimensions28.2 × 3.74 × 3.74 inches
Weight28.7 pounds
ColorStainless Steel
Model4STM4-6/230

06 Frequently asked questions

Is this pump suitable for drinking water?

The product listing identifies the intended use as home irrigation rather than potable water supply. The stainless steel construction resists corrosion, which is good for longevity. However, it is not certified for drinking water standards. You should only use it for garden watering or outdoor tasks.

What is the maximum depth this pump can handle?

This model has a maximum head of 190 feet. This metric indicates the vertical height the pump can push water. It fits moderate depth wells well. Deeper applications may struggle to maintain performance. Always check your specific well depth against this limit before purchasing.

Does it work with standard 110V outlets?

No, this unit requires a 230-volt electrical circuit. It will not operate on standard 115-volt household outlets. You must verify your well site has the correct power supply. Using the wrong voltage can damage the motor or prevent the pump from starting entirely.

How wide is the pump body?

The pump width is 3.74 inches. This size allows it to fit into 4-inch well casings or larger. You need to ensure your well casing is at least this wide. It will not fit in narrower pipes. The length is 28.2 inches.

Is the pump made of plastic or metal?

The listing states the pump body and head are made of stainless steel and SS304. This material choice suggests a design focused on resisting corrosion in deep well environments. It weighs 28.7 pounds. The durable build supports long-term use in wet conditions.

What is the flow rate of this pump?

The pump delivers a maximum flow of 33 GPM. This means it can move 33 gallons of water per minute under ideal conditions. This rate is suitable for irrigation tasks. Flow may drop as you approach the maximum head limit of 190 feet.

07 See also